1. Fundamentals of Force Analysis for Planetary Gear Drives
1.1 Basic Structure and Motion Characteristics
A planetary gear drive consists of four basic components: sun gear (S), planet gear (P), ring gear (R), and planet carrier (C).Common types:

NGW type (2K-H type): Most widely used with high efficiency
NW type: Dual planet gear structure
WW type: Double internal meshing structure
ZUWGW type: Compound planetary drive

1.2 Calculation of Transmission Ratio
For NGW planetary drives:iSRC​=ωR​−ωC​ωS​−ωC​​=−ZS​ZR​​Where:

ω = angular velocity
Z = number of teeth

2. Static Analysis of Planetary Gear Drives
2.1 Basic Assumptions

Friction is neglected
All planet gears carry equal load (ideal manufacturing and assembly)
System is in steady-state equilibrium
Centrifugal and inertial forces are neglected

2.2 Force Balance Equations
2.2.1 Force Analysis of a Single Planet Gear
For the i-th planet gear:

Tangential force: FtSPi​=FtRPi​
Radial force: FrSPi​=FrRPi​
Normal force: FnSPi​=cosαn​⋅cosβFtSPi​​

2.2.2 Force Balance of the Sun Gear
Meshing with n planet gears:∑i=1n​FtSPi​=rbS​TS​​∑i=1n​FrSPi​=0(theoretically)
2.2.3 Force Balance of the Planet Carrier
Bearing reaction forces from planet gears:FCx​=∑FtPi​⋅sinφi​+∑FrPi​⋅cosφi​FCy​=∑FtPi​⋅cosφi​−∑FrPi​⋅sinφi​
2.3 Load Sharing Factor and Load Distribution
Actual load imbalance arises from manufacturing/assembly errors and elastic deformation.Load sharing factor:Kp​=FtPi(avg)​FtPi(max)​​Influencing factors:

Manufacturing errors: pitch error, profile error
Assembly errors: planet gear position accuracy, coaxiality
Elastic deformation: shaft, bearing, housing deformation
Floating mechanism: sun gear or carrier floating improves load sharing

3. Strength Calculation Methods for Planetary Gears
3.1 Contact Fatigue Strength of Tooth Surfaces
3.1.1 Basic Formula (Hertz Contact Theory)
σH​=ZH​⋅ZE​⋅Zε​⋅Zβ​⋅d1​⋅bKA​⋅KV​⋅KHβ​⋅KHα​⋅Ft​​⋅uu±1​​Coefficients:

ZH​: Zone factor
ZE​: Elastic coefficient
Zε​: Contact ratio factor
Zβ​: Helix angle factor
KA​: Application factor
KV​: Dynamic factor
KHβ​: Face load factor
KHα​: Transverse load factor

3.1.2 Special Considerations for Planetary Drives

Internal vs. external meshing: curvature centers on the same side (internal) or opposite sides (external)
Multi-planet effect: Ft(effective)​=n⋅rbS​Kp​⋅TS​​

3.2 Bending Fatigue Strength of Tooth Roots
3.2.1 Basic Formula
σF​=KA​⋅KV​⋅KFβ​⋅KFα​⋅b⋅mn​Ft​​⋅YFa​⋅YSa​⋅Yε​⋅Yβ​Coefficients:

YFa​: Form factor
YSa​: Stress correction factor
Yε​: Contact ratio factor
Yβ​: Helix angle factor
KFβ​: Face load factor
KFα​: Transverse load factor

3.2.2 Special Case for Planet Gears
Subjected to bidirectional bending stress:σFP​=σFSP2​+σFRP2​−σFSP​⋅σFRP​⋅cosθ​Where θ = phase angle between two meshing points
3.3 Bearing Life Calculation for Planet Gears
3.3.1 Bearing Load Analysis

Radial load: Fr​=Fr2​+Ft2​​
Possible axial load (helical gears)

3.3.2 Life Calculation
Basic rating life:L10​=(PC​)p×106 revolutionsWhere:

C: Basic dynamic load rating
P: Equivalent dynamic load
p: Exponent (3 for ball bearings, 10/3 for roller bearings)

3.4 Strength Calculation of the Ring Gear
Load characteristics:

Compressive state in meshing
Deformation of thin-walled rings disturbs load distribution
High stress concentration at root fillets

Strength checks:σHR​=σH​⋅ZR​(Ring gear coefficient)σFR​=σF​⋅YR​(Ring gear root coefficient)
3.5 Strength and Stiffness of the Planet Carrier
3.5.1 Force Analysis
Loads:

Bearing reactions from planet gears
Output torque
Centrifugal force (high speed)

3.5.2 Strength Check
Stress at critical section:σ=WM​+AF​τ=Wp​T​Where:

M: Bending moment
T: Torque
W: Section modulus in bending
Wp​: Section modulus in torsion

3.6 Strength Calculation of the Sun Gear Shaft
Loads:

Torsional stress
Bending stress (unsupported)
Compressive stress (floating design)

4. Standards and Specifications for Strength Calculation
4.1 International Standards

ISO 6336: Calculation of load capacity of spur and helical gears
ISO 9085: Calculation methods for planetary gear drives
AGMA 6123: Design manual for planetary gears

4.2 Safety Factor Selection
Application FieldContact Safety Factor SH​Bending Safety Factor SF​General industry1.0–1.21.4–1.6Automotive transmission1.1–1.31.6–1.8Wind turbine gearbox1.2–1.51.8–2.2Aerospace gears1.3–1.62.0–2.5

5. Summary
Force analysis and strength calculation of planetary gear drives are systematic engineering requiring:

Accurate mechanical models considering actual load distribution and deformation
Comprehensive strength checks: tooth surface, root, bearing, shaft, carrier
Dynamic analysis: vibration, impact, dynamic loads
Manufacturing/assembly effects: error analysis, tolerance design
Service conditions: load spectrum, environment, maintenance

Rational analysis and design ensure compact, high-efficiency, reliable performance. Advances in computing and manufacturing drive higher precision, reliability, and service life.